loading


How the home brew beer yeast recycling

Beer yeast recycling and storage must follow the principle that 'take out in time, low temperature preservation, short-term storage, single strain save' why yeast recycling? Inconvenience in domestic by yeast, the yeast total class is not much also relatively expensive, and if you want to use a liquid yeast, the cost is high. So the yeast recycling becomes a effective way to reduce costs. Recycling yeast it difficult? In fact, as long as pay attention to several points, recycling yeast can has a high success rate and not trouble. Foreign players adapted to the, if you want to control wine budget, yeast recycling can be tried, and Suggestions and yeast culture parallel. Preparation work, Yeast is bottled or barrels of a few days ago) : 2 - boiled 10-3 L of water, continue to boil 15 minutes, this step is to remove the water of oxygen. Cool boiled water, will be stored in a transparent jar. Prepare 4 - 6 pickles can the size of a small jar, advice directly buy a new one. Wash the dry and set aside. Bottled or end of a barrel ( Start preparing recycling yeast) : will finish after bottling or a bucket of yeast slag in the main fermentor, be careful not to pollution, please cover up and cover before you haven't started operation. At this time of the precipitate in fermentor, settlement after the yeast with hot cold slag (in the original wort trub) 。 At this time we will also is the purpose of the activity of healthy yeast and separate hot cold slag. Will be ready for a few days ago have cool boiled water into the barrel fermentation. Cover up and cover, seriously shaking the cold water and sediment mixing ( Be careful not to break the glass fermentor! ) Let stand for 10 - 20 minutes ( The move is to let a healthy yeast would be suspended in the water, cold and hot slag because of gravity, will sink pad on the bottom) Carefully put the most turbid liquid into the big glass jar has disinfection, note at the bottom of the left main fermentor sediment, don't fall over. Repeat shake, let stand for 10 - again 20 minutes ( Let a small amount of sediment with come over again separation) Take out your small glass pickles jar has disinfection. The big glass jar, partial pour into 4 - turbid liquid Six small pickles jar, also be careful not to pour into the sediment. Fast well, hold! Note to 'full' whole pickles jar, try not to leave any air at the top. The move means the same as with boiling water, yeast into dormancy, try not to let it come into contact with air. Cover up and cover quickly to mike pen write the total class and date yeast, throw into the fridge. Done! ! ! Check the next day, a day out you have ice small pickles jar, this time at the beginning of turbid liquid has become clear, there will be a layer of yeast at the bottom of the mat. This mat is baby into dormancy yeast. Entered hibernation reason is: no sugar yeast makes food. The refrigerator temperature is low. The water without oxygen. You are successful! In the future to yeast mat ( 酵母蛋糕) Start the yeast culture, and to enlarge, enough after the yeast population can bring wine! The company's web site: tranogroup. com

GET IN TOUCH WITH Us
recommended articles
knowledge

Have you ever wondered why tin beverage cans are produced at 330ml? We explain why these cans dating back to before World War II were produced in volume fractions of 330ml.

While smaller sized cans such as 200ml and 250ml soft drinks have begun to appear, especially in recent years, we've seen the most popular cans be the 330ml can, as in the past.

The pop-top can is made of aluminum alloy, and its inner wall is coated with some organic coatings to isolate the aluminum alloy from the beverage.

Although the reserves of aluminum in the earth's crust are more than that of iron, the production process of aluminum is much more complicated than that of iron.

In 1959, ERNIE.C.FRAZE of DRT Company in Teton, Ohio, USA (Aimar Clinan Fraze) invented the pop-top can, that is, the material of the lid itself is processed to form a rivet, jacket The last tab is re-riveted and matched with the appropriate notches to complete the lid.

the method of beer filling machine need to hold good to reduce the fault in the process of production, to correctly master the operation method, the use of filling machine to ensure the safe and stable operation of filling equipment.

the advantages of beer barrel cleaning can achieve high efficiency, the use effect of beer barrel in favour of late.

the beer filling machine when use can carry on the filling fast, with high efficiency, which can guarantee good filling effect, so when use tend to be some abnormal problems, these problems will affect the normal use of filling machine, we consult to the filling machine manufacturer, then introduce filling machine manufacturer for everybody to introduce common affliction of filling machine and its solutions.

the beer filling machine when use can ensure fast work efficiency, in order to achieve good working effect, which is the key is to save the use of artificial, automation equipment can also flow to the efficiency of the filling machine play a ', the use of such for filling machine also has a good advantage.

in the process of beer production, and material contact surface of the equipment, due to various reasons will always be some dirt deposition.

Contact Sales at TRANO.

Professional aluminum can manufacturer

Contact us

Contact Person: Mrs.Wang
E-mail: director@packfine.com
Tel: 0086 13054501345
Whats App: 0086 13054501345
We Chat: 13054501345
Address: No. 149 Nandajie Road,Zhifu Area Shandong China

Copyright © 2026 TRANO | Sitemap Privacy Policy
Customer service
detect