loading


How to do a good job in the daily maintenance and maintenance of beer sterilizer?

As we all know, the beer sterilization machine must be maintained and maintained after a certain period of time, so as to ensure the service life of the beer sterilization machine and the use effect of the beer sterilization machine at work. So how to do a good job in the daily maintenance and maintenance of beer sterilizer? 1. The beer sterilizer shall be managed by a special person. The operation shall pay attention to the operation of the refrigeration system, make a good operation record, and stop the maintenance in time if any abnormal situation is found. 2, often check the temperature meter and the valve, found that the valve damage should be replaced in time. 3. When the beer sterilizer is not used for a long time, the pipeline should be cleaned and the accumulated water should be discharged to prevent the cold from freezing and damaging the equipment (Especially the accumulated water in the pump). 4. Check whether there is corrosion pit or damage on the inner wall of the tank. 5. Check whether the mixer is short of oil and whether the oil seal is in good condition. 6. When the freezer group stops using in winter, the accumulated water in the water condenser coil should be drained to prevent the coil from freezing and cracking. 7. Before using the beer sterilizer, the tank must be washed with light hot water, and then disinfected with steam. The material enters the cylinder from the material tube fixed on the tank. The input material should not be too full. 8. At the end of storage, put all the remaining materials in the beer sterilizer tank, rinse them with warm water as soon as possible, brush off the attached materials, and then use 400C ~ 500C alkaline water should be thoroughly cleaned on the inner wall of the container and washed with clean water. Beer sterilization machine is a kind of sterilization machine used by beer production enterprises. In order to increase the service life of beer sterilization machine, the usual repair protection is indispensable. To ensure the service performance of beer sterilization machine, it is very important to take good maintenance measures for machinery!

GET IN TOUCH WITH Us
recommended articles
knowledge

Have you ever wondered why tin beverage cans are produced at 330ml? We explain why these cans dating back to before World War II were produced in volume fractions of 330ml.

While smaller sized cans such as 200ml and 250ml soft drinks have begun to appear, especially in recent years, we've seen the most popular cans be the 330ml can, as in the past.

The pop-top can is made of aluminum alloy, and its inner wall is coated with some organic coatings to isolate the aluminum alloy from the beverage.

Although the reserves of aluminum in the earth's crust are more than that of iron, the production process of aluminum is much more complicated than that of iron.

In 1959, ERNIE.C.FRAZE of DRT Company in Teton, Ohio, USA (Aimar Clinan Fraze) invented the pop-top can, that is, the material of the lid itself is processed to form a rivet, jacket The last tab is re-riveted and matched with the appropriate notches to complete the lid.

the method of beer filling machine need to hold good to reduce the fault in the process of production, to correctly master the operation method, the use of filling machine to ensure the safe and stable operation of filling equipment.

the advantages of beer barrel cleaning can achieve high efficiency, the use effect of beer barrel in favour of late.

the beer filling machine when use can carry on the filling fast, with high efficiency, which can guarantee good filling effect, so when use tend to be some abnormal problems, these problems will affect the normal use of filling machine, we consult to the filling machine manufacturer, then introduce filling machine manufacturer for everybody to introduce common affliction of filling machine and its solutions.

the beer filling machine when use can ensure fast work efficiency, in order to achieve good working effect, which is the key is to save the use of artificial, automation equipment can also flow to the efficiency of the filling machine play a ', the use of such for filling machine also has a good advantage.

in the process of beer production, and material contact surface of the equipment, due to various reasons will always be some dirt deposition.

Contact Sales at TRANO.

Professional aluminum can manufacturer

Contact us

Contact Person: Mrs.Wang
E-mail: director@packfine.com
Tel: 0086 13054501345
Whats App: 0086 13054501345
We Chat: 13054501345
Address: No. 149 Nandajie Road,Zhifu Area Shandong China

Copyright © 2026 TRANO | Sitemap Privacy Policy
Customer service
detect