A Manufacturer and Supplier of Beer Kegs, Beer Keg Washing and Filling Machines, etc.

Solutions and maintenance methods for filling machine manufacturers to analyze machine operation faults

by:Trano     2019-12-14
Nowadays, beer is liked by many people. The beer sold on the market is nothing more than bottled beer and canned beer. Since there is canned beer, there will naturally be filling machine equipment, as the filling machine is used longer and longer, it is inevitable that there will be some minor faults. trano filling machine manufacturers will take you to see the common fault solutions and daily maintenance methods of beer filling machines. I. No filling during automatic operation 1. Failure phenomenon: after the machine is started, no filling will be carried out after the bottle feeding and other actions are in place. 2. Possible causes of failure :(1)Dive lower limit photoelectric position error; (2)Dive down limit photoelectric damage; (3)Equipment parameter setting error; (4)The bottle is not connected to the bottle; (5)The material level filling function is opened and the material level is not arrived; (5)The card bottle cylinder is not played. 3. Steps and methods for filling machine manufacturers to solve faults :(1)Check the alarm interface. Does the lower limit of liquid level give an alarm -? - If there is no alarm, check whether the material level of the material cylinder is sufficient. If it is not sufficient, check whether the line of the liquid level detector is abnormal. If the line is normal, check whether the contact corresponding to the PLC is damaged, if the PLC contact is normal, the liquid level detector is damaged. (2) Check whether the bottle cylinder is punched out after the automatic operation is in place. If the bottle clamping cylinder is not punched out, manually check whether the bottle clamping valve is working. If it is not working, check whether the air pressure is normal and whether the relevant lines are falling off or loose, if there is no abnormality in the above inspection, check whether the contact corresponding to PLC is damaged, and if the PLC contact is normal, the valve body is damaged. (3) When the dive function is turned on during the automatic operation, check the position of the limit photoelectric and photoelectric station-- When the diving cylinder drops to a low position, move the photoelectricity at the lower dive limit to ensure that the photoelectricity indicator at the lower dive limit is on. If the photoelectric indicator cannot be lit, it is necessary to check whether the photoelectric related line at the lower diving limit is normal. If the line is normal, it means that the photoelectric has been damaged and the photoelectric needs to be replaced. (4) When running automatically, check whether the parameters in the touch screen are set incorrectly -? - Check whether the number of filling heads in the parameter setting is set correctly; Check whether the buffer filling amount is set to exceed the target filling amount; Check whether the initial irrigation delay is set too long; Check whether the filling capacity of the filling metering page is set. (5) During automatic operation, after the action is in place, check whether there is a bottle blocking at the photoelectric part of the bottle -? - Adjust the position of the photoelectric switch into the bottle to ensure that the bottle is blocked at the photoelectric part of the bottle during automatic operation. Second, the daily maintenance of the filling machine by the filling machine manufacturer (1) Before each new start-up, check the moisture filter and oil mist device that will start the combination. If too much water is found, it should be dumped in time. If the lubricating oil needs to be filled, it must not be careless. However, in general, lubricating oil can be added once every six months, but if there is an accident, it should be faced flexibly. (2) Always check whether the grounding wire is in firm contact, and also check the starting pipeline, air pressure and motor chain accordingly. If it is found that it is not in normal working condition, the machine should be stopped immediately and repaired. (3) Whether the mechanical parts are in a normal cloud state should also be checked regularly, and then whether each screw is loose should be checked. (4) After each shutdown, we should do a good job in the treatment of fertilizer, and then do a good job in cleaning and sanitation everywhere, which is also a kind of maintenance for machinery. (5) Under normal use, the filling machine cannot be moved or collided. The above is the solution and maintenance method for the filling machine manufacturer to sort out the non-filling solution when the filling machine is running. In addition, the filling machine equipment must pay attention to daily maintenance and cleaning, because this will affect the taste and quality of beer, if you buy equipment, it is recommended to combine your own decoration style and choose the one that suits you. I hope this article can help you. : Filling machine manufacturer
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...
Dear customer, there are too many consultants at present, and you may not be able to reply in time. You can describe what you want, and we will reply you in time.If it is urgently,please contact us +86 13054501345 (WhatsApp and Wechat), E-mail: keg@sskeg.com